I mounted it off center on the lathe. I started by turning the bottom flow of the piece along with a tennon for me to mount this into a chuck. I was then able to reverse the piece and hold the tennon with my oneway chuck. I then progressed inwards from the outer wing working to form the piece's wave similar to what I had outlined on the bottom. I did this portion in steps to ensure that I didn't make any portion to weak to support the tension of the turning on the outer edges. As I got to the center, I started to outline the vessel and give it shape. The hardest part was defining the bottom of the vessel. Due to where the wings of the piece are and the angle to get the bottom, this posed some major problems I'm still working on. Bruce had used some custom tools he ground just for this purpose. Basically they were right angle bent tools for scraping and a pointed tool to get into the bottom corner. I then removed the tailstock and hollowed out the vessel. This proved to be the easiest of the project. I then did a LOT of sanding. Both with the lathe on, and with it off. The vessel was mainly done with the piece spinning, everything else very carefully with the lathe off. I then turned a jam chuck, re-mounted the vessel inside the jam chuck and cleaned up the bottom. It was then I realized that the shape of under the vessel should have been rounded not done like a normal bowl or vessel bottom. I hope you enjoy...
Monday, April 7, 2008
Bruce Perry Inspired piece
I mounted it off center on the lathe. I started by turning the bottom flow of the piece along with a tennon for me to mount this into a chuck. I was then able to reverse the piece and hold the tennon with my oneway chuck. I then progressed inwards from the outer wing working to form the piece's wave similar to what I had outlined on the bottom. I did this portion in steps to ensure that I didn't make any portion to weak to support the tension of the turning on the outer edges. As I got to the center, I started to outline the vessel and give it shape. The hardest part was defining the bottom of the vessel. Due to where the wings of the piece are and the angle to get the bottom, this posed some major problems I'm still working on. Bruce had used some custom tools he ground just for this purpose. Basically they were right angle bent tools for scraping and a pointed tool to get into the bottom corner. I then removed the tailstock and hollowed out the vessel. This proved to be the easiest of the project. I then did a LOT of sanding. Both with the lathe on, and with it off. The vessel was mainly done with the piece spinning, everything else very carefully with the lathe off. I then turned a jam chuck, re-mounted the vessel inside the jam chuck and cleaned up the bottom. It was then I realized that the shape of under the vessel should have been rounded not done like a normal bowl or vessel bottom. I hope you enjoy...
Thursday, April 3, 2008
Bruce Perry Demo - March 2008
Winged Bowls
Presented by: Bruce Perry
Reported by: John I. Giem
On


One of Bruce’s winged bowls.
For the demo, Bruce used a piece of rectangular spalted birch about six inches by ten inches. He mounted off-center toward one corner between centers on the lathe. At the headstock, he used a disk covered with sandpaper mounted in a chuck. A live cup center without a center pin was used in the tailstock. He believes that a screw center has too high of a risk toward coming loose.
- The turning speed is critical. The faster it turns, the easier to cut and get a smooth finish. If it is turning at the resonance speed then the lathe will vibrate heavily and move all over the place. The turning speed MUST be either below or above the resonance.
- The initial cut was an arcing cut from inside to outside.
- He often uses a bandsaw to remove part of the waste after the initial shaping.
- The tailstock will eventually get in the way preventing the rubbing of the bevel on the gouge. At this point he switched to a bowl gouge with a straight across grind. This allows the continuation of bevel rubbing resulting in better control and smoother cuts.
- A tenon was turned on the bottom of the piece (that side toward the tailstock). He wants just enough to mount in the chuck be strong enough to hold but not so much that it interferes with the design.
- Uses a skew as a negative rake scraper to help smooth the surfaces.
- When he reverse mounted the piece using the tenon and chuck, he also used the tailstock to help stabilize the work.
- Keep the tool rest close to the work to give good support to the turning tools but yet far enough away so that the tool is supported on the shaft not its’ bevel.
- Cut from the outside toward the center leaving the thicker sections toward the center. If one were to cut from the center outward, then the thinner inner sections would work like a hinge allowing the outer rim to flex and vibrate.
- For better control, keep the tool rest parallel to the path of the cut.
- He turns the outer edge to about ¼ inch thick.
- When the cutting of the wing approaches the base of the pot or bowl, the clearances get tight andthere is the risk of catching the wing of the gouge and causing a ‘dig in’. To avoid this, he
switches to a spindle gouge and specially shaped scrapers.
- When possible, use heavier (thicker) tools to minimize unwanted vibrations.
- The scraper he uses to carve out the base near the bowl is a specially ground hooked negative rake scraper. Since this scraper gets relatively little usage, he ground it from an inexpensive carbon steel skew.
- He finds that the wings of the piece look better if they are just a little thicker at the outer end and a little thinner on the curve going back to the pot.
- He drilled a depth hole in the center of the pot (vessel) using a spindle gouge.
- Small hollowing tools with a negative rake were used to hollow the small vessel.
- He remounted the piece with the vessel mounted on a jam chuck. The chuck was custom turned to fit on the outside ‘downhill’ side of the bowl. There was a ¼” hole drilled through the chuck so that if the piece got stuck on the chuck, it could be removed using compressed air through the hole. The tailstock was used to hold the piece firmly on the jam chuck.
- The wings are sanded without the lathe rotating by using a two inch random orbit sander. The tool rest is removed while sanding to provide more room and access.
- He will use about three applications of sanding sealer before starting to sand.
- The sanding sealer will help stabilize the softer portions of the spalted birch. These softer sections are difficult to get smooth with the turning tools due to their softness. The sealer will improve their durability.
- Bruce took the piece home with him where he will finish the finial turning, sanding and finishing. He will bring it to the Symposium in September and enter it for auction to support the education grants.
Friday, December 14, 2007
So... why not some of my work

Let's start out with my Birthday cake from this year. It's almost as if Tammy knew exactly what I wanted.
Here's a few item's I've turned recently;
Last night I worked on an Ash bat for a friend of ours. She wanted to give it to her boyfriend for Christmas. It actually turned out pretty good and now Tammy wants on.

This is a Aspen vase I made to fit in a stand I had sitting around. It's not finished yet as I'm still trying to decide what kind of finish/finish work I want to do to it.
An Alder basket weave bowl I turned and burned. There's a basket weave patter on the top rim that was burned in.
A nice box elder bowl. Stands about 7" high and 10" across
One of my favorite pieces so far. A Cedar hollow form/vase that I turned, dremeled out the holes and burned with a butane torch

side view

This is one of my Elm vases I turned in the Trent class earlier this year. Finally got it dried and finished.
Some mini turnings I did. The walnut one (right) is about 2" high.
Another Mini. About 1" high, with a burned in pattern
This is from a piece of Old Pithy pine I had sitting around and decided to mess with one day. Sure glad this didn't become firewood.
And my winged aspen bowl. Turned completely on the lathe and the wings are left for artistic value on the piece.
